图片展示

ADIN1300

产品详情

Features and benefits

· 10BASE-Te/100BASE-TX/1000BASE-T IEEE® 802.3 compliant

· MII, RMII, and RGMII MAC interfaces

· 1000BASE-T RGMII latency transmit < 68 ns, receive < 226 ns

· 100BASE-TX MII latency transmit< 52 ns, receive < 248 ns

· EMC test standards

· IEC 61000-4-5 surge (±4 kV)

· IEC 61000-4-4 electrical fast transient (EFT) (±4 kV)

· IEC 61000-4-2 ESD (±6 kV contact discharge)

· IEC 61000-4-6 conducted immunity (10 V)

· EN55032 radiated emissions (Class A)

· Unmanaged configuration using multilevel pin strapping

· EEE in accordance with IEEE 802.3az

· Start of packet detection for IEEE 1588 time stamp support

· Enhanced link detection

·Configurable LED

· Crystal oscillator frequency/25 MHz clock input frequency (50 MHz for RMII)

· 25 MHz/125 MHz synchronous clock output

· Small package and wide temperature range

· 40-lead, 6 mm × 6 mm LFCSP

· Specified for −40°C to +105°C ambient operation

· Low power consumption

·330 mW for 1000BASE-T

· 140 mW for 100BASE-TX

· 3.3 V/2.5 V/1.8 V MAC interface VDDIO supply

·Integrated power supply monitoring and POR



Product details 

       The ADIN1300 is a low power, single port, Gigabit Ethernet transceiver with low latency and power consumption specifications primarily designed for industrial Ethernet applications.

       This design integrates an energy efficient Ethernet (EEE) physical layer device (PHY) core with all associated common analog circuitry, input and output clock buffering, management interface and subsystem registers, and MAC interface and control logic to manage the reset and clock control and pin configuration.

       The ADIN1300 is available in a 6 mm × 6 mm, 40-lead lead frame chip scale package (LFCSP). The device operates with a minimum of 2 power supplies, 0.9 V and 3.3 V, assuming the use of a 3.3 V MAC interface supply. For maximum flexibility in system level design, a separate VDDIO supply enables the management data input/output (MDIO) and MAC interface supply voltages to be configured independently of the other circuitry on the ADIN1300, allowing operation at 1.8 V, 2.5 V, or 3.3 V. At power-up, the ADIN1300 is held in hardware reset until each of the supplies has crossed its minimum rising threshold value. Brown-out protection is provided by monitoring the supplies to detect if one or more supply drops below a minimum falling threshold (see Table 17 on the datasheet), and holding the device in hardware reset until the power supplies return and satisfy the power-on reset (POR) circuit.

       The MII management interface (also referred to as MDIO interface) provides a 2-wire serial interface between a host processor or MAC (also known as management station (STA)) and the ADIN1300, allowing access to control and status information in the PHY core management registers. The interface is compatible with both the IEEE 802.3 Standard Clause 22 and Clause 45 management frame structures.

       The ADIN1300 can support cable lengths up to 150 meters at Gigabit speeds and 180 meters when operating at 100 Mbps or 10 Mbps.

Applications

· Industrial automation

· Process control

· Factory automation

· Robotics/Motion Control

· Building automation

· Test and Measurement

· Industrial IoT



ADIN1300
Long press to look detail
Long by picture save/share

Leave a message

  • Name

  • Phone *

  • E-mail

  • Leave a message

  • Submit

  • Security Code
    Refresh the code
    Cancel
    Confirm

 

ADI

TI

Advantech

ICOP

Innalabs

ABOUT US  

 

About Us

Company Technology

Company Honor

www.omochip.com

Copyright ©  OMO Development Co,.Ltd.All Rights Reserved.

Service Center
Contacts
热线电话
0755-26902425
上班时间
周一到周五
E-mail
jane@omochip.com
Qrcode
Qrcode
Service Center
添加微信好友,详细了解产品
使用企业微信
“扫一扫”加入群聊
复制成功
添加微信好友,详细了解产品
我知道了